top of page

Restoring a Tascam 246

joepampel
Oct 8
5 min read

When I was in recording school the home recording revolution was in its infancy. The Tascam 246 was introduced while I was enrolled and all of us were blown away by what it could do. I saved up and bought one after I graduated and started the punishing ritual of trying to write and record original songs.


I recently found it in the basement, I thought it was long gone. I tried to clean the pinch roller but it was just goo. The capstan didn't turn either. Nowhere to go but up.


Step 1: Find the service manual. Thankfully it was online. (link below)

Step 2: Find someone selling the replacement parts (belts, tires & pinch roller)

Step 3: Dive in.


Considering how much stuff they packed in, the deck comes apart pretty nicely. And in a nice change from the usual, the service manual has guidance around how to remove various parts. Thank you, people of Tascam.


The 246 uses 2 belts; a flat belt for the capstan and a square belt for the control motor (moving the heads in and out etc.) There are also 2 idler tires, and of course the pinch roller.


I took off the rear cover and started cleaning off the bits of old belt "goo" that were there. I used Iso and Q-tips, dozens of q-tips. I found that soaking a paper towel in iso and using a dental pick to push it into tight spots was also helpful, especially for the tight "v" of the control belt pulleys. Get them spotless. Mine had bits of belt down deep that took a while to clean out.


  • In hindsight, I should have taken off both covers first. Removing the top cover gives you good access to the tape transport and I might not have had to remove the transport if I had done this. (It also provides a nice opportunity to clean 40 years of finger schmutz off of the knobs and panel).


The control belt can just be slipped on. The capstan belt requires you to loosen the backing plate (2 screws) that the capstan sits in.


The idler tires can be slid over the pulleys without having to remove the assembly. I used a pair of dental picks for this.


The pinch roller is set into an arm and there is a locating pin to hold it in place. An e-clip fastens the arm to it's pivot. Remove the clip and then the arm, noting how the spring is positioned. I tried to tap the pin out that holds the roller in place, but it didn't want to move. So I gently pried up on the arm to let me pivot the pinch roller out. Once out, the pin was loose and I just put it back in to secure the new roller. Be sure to oil the pin, it's a tight fit and you want the roller to spin freely.


I used DeOxit D5 on a paper towel to clean the RCA jacks, and sprayed some on a 1/4" TRS plug to try and clean up the jacks. While the deck was apart I removed the 4-screws holding the lower board in place so I could pivot it out of the way to provide access so I could clean the pots and switches. The channel function switches were especially cranky. (record/off/playback)


The deck would now play a tape but the speed was way off, much too fast. There are a pair of trimmer pots on a board next to the tape transport where you can calibrate the speed. I used one of my old 4-track tapes as a reference and adjusted the speed until the track was at concert pitch. I want those tapes to play properly on this deck.


The noise level and frequency response sound fine, actually much better than I remember so I'm leaving those settings alone.


I used automotive plastic cleaner for most of the control panel & plastic polish for the meter bezels which were starting to yellow a bit. Some hot soapy water to soak in and an old toothbrush took care of the knobs.


Pics

68 knobs pull right off and then there are 2 sets of screws, one for the lower cover and then a set for the upper cover. The only "trick" screw is in the middle of the chassis and runs through the large PCBs. When you re-assemble the case, just watch the record/arm LEDs in the middle. They are pretty floppy and can easily get bent over as the top cover lowers back on.


How it started.  No belts, hidden goo around the chassis. Good times. To remove the tape transport there are 5 screws, then you clip those two wire ties on the left and finally remove the center plug to the control board just above it. It does give you very good accessibility if you need it. In hindsight I probably did not need to remove the transport, I only needed to remove the top cover to access the idler tires and pinch roller.
How it started. No belts, hidden goo around the chassis. Good times. To remove the tape transport there are 5 screws, then you clip those two wire ties on the left and finally remove the center plug to the control board just above it. It does give you very good accessibility if you need it. In hindsight I probably did not need to remove the transport, I only needed to remove the top cover to access the idler tires and pinch roller.
I kept finding more bits of the capstan belt around the chassis.
I kept finding more bits of the capstan belt around the chassis.
The old pinch roller was goo. It got on everything.  Luckily Iso was enough to clean it up.
The old pinch roller was goo. It got on everything. Luckily Iso was enough to clean it up.
The new capstan belt is in place. There are 2 screws under the wires running across that metal bar behind the capstan itself. Then you can lift it just enough to get the belt through.
The new capstan belt is in place. There are 2 screws under the wires running across that metal bar behind the capstan itself. Then you can lift it just enough to get the belt through.
New control belt in place.  It took a while to get all of the old goo out of the pulleys.
New control belt in place. It took a while to get all of the old goo out of the pulleys.
This is just after removing the old idler tires (the white wheels in upper RH of photo). I had to clean up these pulleys as well. The tires had chunks missing from them.
This is just after removing the old idler tires (the white wheels in upper RH of photo). I had to clean up these pulleys as well. The tires had chunks missing from them.
The new pinch roller in place
The new pinch roller in place
New idler tires in place. I just slid them gently over the pulleys so I didn’t have to take it apart.
New idler tires in place. I just slid them gently over the pulleys so I didn’t have to take it apart.
Close-up of the control board with the tape speed trimmers. Upper is 3-3/4, lower is 1-7/8.
Close-up of the control board with the tape speed trimmers. Upper is 3-3/4, lower is 1-7/8.
Post clean up and service. Fancier than the Tascam 144 Springsteen used for “Nebraska”, but with a clear lineage to it.
Post clean up and service. Fancier than the Tascam 144 Springsteen used for “Nebraska”, but with a clear lineage to it.

Some of the more interesting features:

  • You could disable the dBX noise reduction on all of the tracks or just track 4 if you needed to record SMPTE time code.

  • Each channel had a 1/4" TRS insert jack on the rear, this is in addition to the 2 FX busses on the front panel. I had a whole patchbay wired up to this back in the day.

  • Bouncing down was simple given the track assignment buttons and the Record arming buttons. ('record function')

  • The meters could display signal level on the FX busses, the monitor mix or the program mix. They all have peak/hold LEDs which is a nice touch.

  • Varispeed on both tape speed settings. Before we had autotune we had 'slow the tape'.

  • Each mixer channel could take mic level or line level signals.

  • Separate 4-channel monitor mix section (level & pan) with the ability to send the program or monitor mix to the headphones.


Only real bummer?

  • There are no balanced inputs so you need either an adapter or an outboard mic pre with a 1/4" output if you have pro mics.



 
 
 

Comments

Rated 0 out of 5 stars.
No ratings yet

Add a rating
Post: Blog2_Post
bottom of page